Just did a fresh install with skudonet CE.

I'm able to configre the first NIC with IP 10.10.xx.110

But when I edit the second NIC and what to add 10.10.xx.111

it complains that this is already configured on ETH0?

I can't really find much on using websockets over this particular proxy. I've had good luck with HAProxy, but I'm trying to move AWAY from HAProxy :)

I’ve added new services for other domains, but the reverse proxy doesn’t work for them — as if there’s a limit on the number of services — although I haven’t seen any mention of such a limitation in the documentation. The resource usage graphs in the Proxmox monitor look fine.

I’ve configured the same setup using NGINX Proxy Manager and it works, but I need the WAF feature provided by Skudonet.

The apps are running inside Docker, and each app listens on a different port — 1080, 1081, 1082, 1083, etc. The reverse proxy helps me route these specific ports, something I can’t configure directly through Cloudflare.

What could be the issue?

This is a fully clean install. All I did was deploy Bookworm, set a static IP and went through the install instructions. I'm stuck.

Also, we have two issues righ now, one with memory and one with farms graphics.

for the memory we have found that suddenly memory goes up, we have two nodes with 8GB ram each, is there any special configuration on how to handle this?

On the other side, we are not able to get the Farms graphs, despite having connections we see nothing on the graphs. I attached an image where you can see the issue.

Is there any documentation where we can see how many concurrent sessions can we have in this version?

Again, thanks for your help, I really hope you can guide me again.

mount: mouinting /dev/vda on /media failed: Invalid argument

next Installation continues

Select location, select keyboard, configure network, set up users, configure clock, disk patitioning, installing base system.

Then the installation stops at:

Configure the package manager!!!

pressing ALT-F2

gives me the "BusyBox"

Here I need to unmount the CDROM manually, then return to the installation screen ALT-F1 and select a new mirror site.

Installation continues

The after installing the software I run into the next problem "Select and install software"

Then Skip and continue to install bootloader

Then Finishing the installation

the OS is running but SKUDONET is not installed!

Here are the logs that might help. I also tried the command on farmguardian check_udp_nc manually and it worked.

Thank You.

We were working smoothly with our cluster, but we have found that memory suddenly goes up and that we needed to make a failover, but as soon as we did that some interfaces stopped working, I mean we only have 4 virutal interfaces, when working on node1 everything was ok, with the failover to node2, 2 interfaces stopped working even with an ok status, but we couldnt use the farms that were on those interfaces, Do you know what could be happening?

Thanks in advance

The Dashboard memory show that almost all memory is in use see attached pic.

system:

label_importantSKUDONET Version: 7.2.1

label_importantWebGUI Version: 1.3.1-7.2.1

label_importantAppliance Version: SKD 7

label_importantKernel Version: 6.1.0-27-amd64

label_importantHostname: LB-SKDCE7-1

label_importantSystem Date: Mon Feb 3 20:52:01 2025

on terminal:

  free -m
total used free shared buff/cache available
Mem: 3915 537 125 0 3532 3377
Swap: 974 0 974

Top command:

top - 20:57:11 up 7:25, 2 users, load average: 0.00, 0.00, 0.00
Tasks: 136 total, 1 running, 135 sleeping, 0 stopped, 0 zombie
%Cpu(s): 0.7 us, 1.0 sy, 0.0 ni, 98.3 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st
MiB Mem : 3915.3 total, 116.8 free, 545.8 used, 3533.0 buff/cache
MiB Swap: 975.0 total, 974.7 free, 0.3 used. 3369.5 avail Mem

please advise how to fix cpu dashboard usage.

Regards,

Yohai